Ford 4R100 Transmission c/w Filter Kit 1999-2003 7.3L. The stock transmission is designed to handle the output of the stock engine, but not much more. Increase the durability of your drivetrain with a BD transmission. BD transmission and converter clutches are made from specialized, high-performance materials, and 33% more clutch surface is added to eliminate slippage. A re-programmed valve body with improved valve designs, higher line pressure and enhanced oil flow creates positive clutch apply, which results in quick, sharp shifts. A BD deep-sump aluminum.
Ford 5 Speed Manual Transmission ZF-S547 Providing You WithIssues Rebuild or Replacement Components, Ask an Expert.
Problems with your ZF-S547 Manual Transmission if notcorrectlyidentifiedcan be veryexpensive and cost you plentyof cashas well asdown timeaccording to Manual Transmission Rebuild professional Dan Schoenfelder of Midwest Transmission Center Zumbrota, MN. Below Dan provides5of the very mostcommon ZF S5-47 Manual Transmission breakdowns. Midwest Transmission Center can provide ZF-S547 Transmission rebuilt units as well as parts andfreetechnicalassistance withyour own transmission repairs. If you’d likesevere duty and generally aredamaging gears and or main or counter shafts we offer cryogenic heat-treated replacements, this canadd about 30% to the strength over the OE parts.
Ford starting using the ZF-S547 in 1995 to 1998 utilized the S547M was utilized between 1999 to 2001, this transmission is rated for 470 lb-ft. input torque all gears are synchronized. The particular unit came in2 different ratios wide and close ratio variations. The close ratio editionis utilized in F-Series trucksusing a 7.3 Lt diesel engine and a gross vehicle weight over 8500 lbs.
This transmission features an lightweight aluminum case having an integral bell housing. The ZF transmission used with the 7.3 Lt diesel engines requiresuse of synthetic Motorcraft MERCON ATF fluid. Rebuilt Manual ZF-S547 Transmission can be purchasedfrom Midwest Transmission Center, we can easilyalso provide rebuild overhaul kits and hard-parts, inquire about our great take out parts, (used) let ushelp save you some money!
Fiveof the extremely common problems in ZF-S547 manual transmission failurestend to be:
Noiseonacceleration and speed, ZF-S547 Noise upon deceleration
This problemmay betracked to failure of the pilot bearing in the flywheel, alsoexamine to ensure that the fluid level is correct. Youshould alsoexamine the bearing between your input and main shaft. Rough and excessive wear on therear bearing on the output shaft. Noise can even becaused bysubstantialuse of needle bearings under main-shaft gears.
This problemmay betracked to failure of the pilot bearing in the flywheel, alsoexamine to ensure that the fluid level is correct. Youshould alsoexamine the bearing between your input and main shaft. Rough and excessive wear on therear bearing on the output shaft. Noise can even becaused bysubstantialuse of needle bearings under main-shaft gears.
Hard to get to get into gear ZF-S547
1st, 2nd and reverse might beattributed tofailing clutch. And or failureof your reverse syncro ring/slider.
1st, 2nd and reverse might beattributed tofailing clutch. And or failureof your reverse syncro ring/slider.
Grinding going into gear ZF-S547
Syncro ring or slider wear, excessive bearing wear allowing shafts to moveaway from design boundaries. An additional common problem is excessively worn shift housing or shifter, each of whichcan replace by re-manufactured componentsby Midwest Transmission Center.
Syncro ring or slider wear, excessive bearing wear allowing shafts to moveaway from design boundaries. An additional common problem is excessively worn shift housing or shifter, each of whichcan replace by re-manufactured componentsby Midwest Transmission Center.
Popping out of gear ZF-S547
May bebrought on by worn syncro slider and orperhaps shift lever maladjusted. Worn input bearing as well as shift shaft.
May bebrought on by worn syncro slider and orperhaps shift lever maladjusted. Worn input bearing as well as shift shaft.
Will not shift through gear to gear ZF-S547
This issuemay bebrought on bythe examples below: Shift fork pads missingor with abnormal wear, damaged fork or slider grooved.
This issuemay bebrought on bythe examples below: Shift fork pads missingor with abnormal wear, damaged fork or slider grooved.
The ZF-S547 transmission can alsoreceivedamage to the front case 1 / 2 (bell housing) and maybe the rear extension housing because of a damaged drive shaft, bent, out of balance, excessive wear of u-joint or yoke. At the very firstsign ofvibrationwe suggestthat you have the driveline high-speed balanced. Malfunctionof your dual mass flywheel can alsocrackthe actual bell housing portion of the case.
Call now 888-824-2012 to order a rebuilt ZF-S547 manual transmission or parts; buy the parts from Midwest Transmission Center and youneed helpjustcall the Drivetrain Expert 1-888-834-2012 it’sfree of charge, we’ve gotthe actual answers you will need. To find out more see our web site at https://www.midwesttrans.com/zf547.html
Usually Ships in 24 to 48 Hours
$455.00
Usually Ships in 24 to 48 Hours
$249.95
Usually Ships in 24 Hours
$495.00
Usually Ships in 24 Hours
$239.00
Usually Ships in 24 Hours
$27.95
Usually Ships in 24 hours
7.3 Transmission Removal
![7.3 Transmission 7.3 Transmission](/uploads/1/1/2/0/112027665/506763001.jpg)
$31.40
7.3 Powerstroke 1994-2003 Only Fits Aftermarket Billet Converter
![Ford Ford](/uploads/1/1/2/0/112027665/107330563.jpg)
Super Duty 1989-2010 (With E4OD, 4R100 & 5R110 Trans)
Usually Ships in 24 Hours
$334.95
Ships Directly From The Manufacturer (1-3 Days)
$150.35
Ships Directly From The Manufacturer (5-7 Days)
7.3 Transmission Leak
$1,664.95
Ships Directly From The Manufacturer (5-7 Days)
Best Transmission For 7.3 Diesel
$419.95
Ships Directly From The Manufacturer (1-3 Days)
$807.50
Usually ships in 24 hours
$141.99